Yongjian Machinery6 min read
Argon arc or laser welding for stainless tube: how to choose
Argon arc or laser welding for decorative stainless tube? What each method does, what the choice depends on, and what to ask the factory.
Buyers comparing stainless tube mills often reach the same fork early, especially when choosing a decorative stainless pipe welding method: argon arc welding or laser welding. Both close a continuous seam along the formed strip, and both are in use across the industry. Neither is the right answer for every plant, and a quotation that picks one for you without asking about your product has skipped the important part.
This guide sets out what each method is, what the choice depends on, and the questions worth putting to any factory before you commit. It does not tell you which one to buy. That depends on your tube, your customers and what you do after welding, and the factory needs those details before it can give you a straight answer.
What the two methods are
Argon arc welding (also known as TIG or GTAW) melts the strip edges with an electric arc struck from a non-consumable tungsten electrode. Argon gas shields the molten metal from the air so the weld does not oxidise. On a tube mill the torch sits in a fixed position over the seam, and the formed strip passes beneath it after the squeeze rolls have brought the edges together. It is a long-established method on stainless tube, and many operators and maintenance staff already know how to set it up and keep it running.
Laser welding melts the edges with a focused beam of light instead of an arc. The energy goes into a much smaller spot, so the heat is concentrated in a narrower band along the seam. The weld still needs gas shielding, and the line still needs the same uncoiling, forming, sizing, straightening and cutting sections as any other tube mill. What changes is the heat source, and everything that has to be right for that heat source to work.
That last point matters. Because the spot is small, the strip edges have to meet consistently where the beam expects them. Strip edge condition, forming setup and seam guidance all carry more weight on a laser line. A laser source is also a different piece of equipment to look after, with its own optics, cooling and safety enclosure, and it calls for different skills from the people who maintain it.
What the choice depends on
Wall thickness and the size range you run
Wall thickness drives most decisions on a tube mill, and the weld method is no exception. Each method has a range of wall thickness it handles well on a given line, and those ranges differ between machine editions. Do not assume either method covers your whole product range. Bring your full list of sizes, with the thinnest and the heaviest wall you intend to run, and ask the factory to confirm which edition covers which part of it.
Finish and end use: decorative or industrial
For decorative tube (handrail, balustrade, furniture, display fittings) the customer sees the outside surface. The seam is ground and the tube is polished, and the real question is how the seam looks after that. What matters is the shape and width of the bead the welder leaves, how much grinding it takes to remove, and whether any trace of the seam shows through the final finish.
For industrial tube, meaning pipe that carries fluid or works in a corrosive environment, appearance comes second. What matters is a sound weld through the full wall, the condition of the inside bead, and the corrosion resistance of the zone either side of the seam. Ask how each of those is controlled and checked on the line you are offered.
What you do downstream
This is the factor buyers most often leave until after the order, and it should come first. The weld method interacts with three downstream steps.
Polishing. On decorative tube, whatever bead the welder leaves has to be ground and polished away. A small, even bead is less work for the grinding and polishing stages; a wide or irregular one is more. Judge the bead the line actually produces on sizes like yours, not a description of it.
Inner weld levelling. Where the bore matters (fluid lines, tube that will be cleaned internally, tube that something has to pass through) the inside bead may need to be flattened. Whether you need inner weld levelling depends on the end use. Whichever weld method you choose, the line needs room and provision for it if you do.
Annealing. Welding heats stainless steel locally, and the zone around the seam can lose part of its corrosion resistance. For fluid service and corrosive environments, solution annealing restores it; we explain the metallurgy in Why welded stainless pipe corrodes along the seam. The point here is that a change of heat source does not by itself settle whether you need annealing. The application settles it.
If polishing, levelling or annealing is part of your plan, specify it together with the mill rather than adding it later. Each step takes floor length, power, utilities and controls, and all of those are easier to plan before the line is built than after.
Who will run and maintain it
Arc and laser welding ask different things of the people on your floor. Think about who will set the welding parameters, who will replace the electrode or clean and check the optics, and who will diagnose a bad seam at the start of a night shift. More automated control takes some of that load, but someone on site still has to understand the system well enough to trust it and to know when not to.
What Yongjian Machinery makes
Yongjian Machinery builds stainless steel welded tube mill lines. Our 2024 catalogue lists the decorative pipe making machine in two forms:
- with argon arc welding, and
- a laser-welded edition with intelligent electronic control, our laser welded stainless pipe machine.
The same catalogue lists the downstream equipment discussed above: inner weld levelling, online solution annealing, and round and square tube polishing machines, alongside industrial pipe making machines and moulds. The company began in 1999 making stainless tube moulds and polishing machines, before decorative and industrial pipe equipment became its core products.
That means the welding decision and the steps after it can be discussed together, as one line, with one supplier.
Questions to bring to the factory
- For each of my sizes and wall thicknesses, which edition covers it: argon arc, laser, or both?
- Can I see a line welding tube close to mine, on video or on a video call with an engineer?
- What does the weld bead look like straight off the welder, and after grinding and polishing to the finish I sell?
- What strip edge condition and slitting quality does the welder need to run reliably?
- What does the welder need day to day: shielding gas, cooling, consumables, and which parts wear?
- What will my operators and maintenance staff need to learn, and what support is there for installation and commissioning?
- If I need inner weld levelling, annealing or polishing, how are they built into the line, and what do they add to its length and its utility requirements?
- Which material grades will I run, and does that change anything about the welding set up you would propose?
For the rest of the specification (machine class, changeover, tooling, compliance and site preparation) see How to specify a stainless steel tube mill.
Next step
Send us your tube sizes, wall thicknesses, material grade, finish and end use, and tell us what happens to the tube after welding. We will come back with a proposed line configuration and the reasoning behind it. You can also request our catalogue, or ask for a video call or a factory visit through the enquiry form.
- Buying guide
- Tube mills
- Welding